Friction

Related Topics:
Friction

Friction is the force that opposes the relative motion or tendency of such motion of two surfaces in contact. It is not, however, a fundamental force, as it originates from the electromagnetic forces and exchange force between atoms. In situations where the surfaces in contact are moving relative to each other, the friction between the two objects converts kinetic energy into heat (atomic vibrations). Friction between solid objects and fluids (gases or liquids) is called fluid friction. See also aerodynamics and hydrodynamics.

Friction is an extremely important force - it propels automobiles and other ground transport and holds nails, screws and nuts, along with many other uses.

Equations

The classical approximation of the force of friction known as Coulomb friction (named after Charles-Augustin de Coulomb) is expressed as:

F_f = \mu N

, where

\mu

is the coefficient of friction,

N

is the force normal to the contact surface, and

F_f

is the force exerted by friction. This force is exerted in the direction opposite the object's motion.

This law mathematically follows from the fact that contacting surfaces have atomically close contacts only over extremely small fraction of their overall surface area, and this contact area is proportional to load (until saturation takes place when all area is in atomic contact thus no further increase of friction force takes place).

This simple (although incomplete) representation of friction is adequate for the analysis of many physical systems.

Coefficient of friction

The coefficient of friction (also known as the frictional coefficient) is a dimensionless scalar value which describes the ratio of the force of friction between two bodies and the force pressing them together. The coefficient of friction depends on the materials used -- for example, ice on metal has a low coefficient of friction (they slide past each other easily), while rubber on pavement has a high coefficient of friction (they do not slide past each other easily). Coefficients of friction need not be less than 1 - under good conditions, a tire on concrete may have a coefficient of friction of 1.7. Magnetically attractive surfaces can have very large friction coefficients, and glued or welded together surfaces have infinite friction coefficient. Sliding (dynamic) friction and static friction are distinct concepts. For sliding friction, the force of friction does not vary with the area of contact between the two objects. This means that sliding friction does not depend on the size of the contact area.

When the surfaces are adhesive, Coulomb friction becomes a very poor approximation (for example, Scotch tape resists sliding even when there is no normal force, or a negative normal force). In this case, the frictional force may depend on the area of contact. Some drag racing tires are adhesive in this way (see, for example, ^*).

The force of friction is always exerted in a direction that opposes movement (for kinetic friction) or potential movement (for static friction) between the two surfaces. For example, a curling stone sliding along the ice experiences a static force slowing it down. For an example of potential movement, the drive wheels of an accelerating car experience a frictional force pointing forward; if they did not, the wheels would spin, and the rubber would slide backwards along the pavement. Note that it is not the direction of movement of the vehicle they oppose, it is the direction of (potential) sliding between tire and road.

The coefficient of friction is an empirical measurement -- it has to be measured experimentally, and cannot be found through calculations. Rougher surfaces tend to have higher values. Most dry materials in combination give friction coefficient values from 0.3 to 0.6. It is difficult to maintain values outside this range. A value of 0.0 would mean there is no friction at all. Rubber in contact with other surfaces can yield friction coefficients from 1.0 to 2.0. A system with "interlocking teeth" between surfaces may be indistinguishable from friction, if the "teeth" are small, such as the grains on two sheets of sandpaper or even molecule-sized "teeth".

The coefficient of friction, when multiplied by the reaction force on the object by the contact surface, will give the maximum frictional force opposing sliding on the object. However, if the force pulling on the object is less than the maximum force of friction then the force of friction will be equal to the force pulling on the object. You have to pull with a force greater than the maximum value of friction to move the object.

Types of friction

Static friction

Static friction (informally known as stiction) occurs when the two objects are not moving relative to each other (like a desk on the ground). The coefficient of static friction is typically denoted as μ_s. The initial force to get an object moving is often dominated by static friction. The static friction is in most cases higher than the kinetic friction. That is why you feel a jerk when starting to move and when stopping.

Rolling friction occurs when one object "rolls" on another (like a car's wheels on the ground). This is classified under static friction because the patch of the tire in contact with the ground, at any point while the tire spins, is stationary relative to the ground. The coefficient of rolling friction is typically denoted as μ_r.

Limiting friction is the maximum value of static friction, or the force of friction that acts when a body is just on the verge of motion on a surface.

Kinetic friction

Kinetic (or dynamic) friction occurs when two objects are moving relative to each other and rub together (like a sled on the ground). The coefficient of kinetic friction is typically denoted as μ_k, and is usually less than the coefficient of static friction. From the mathematical point of view, however, the difference between static and kinematic friction is of minor importance: Let us have a coefficient of friction which depends on the sliding velocity and is such that its value at 0 (the static friction μ_s ) is the limit of the kinetic friction μ_k for the velocity tending to zero. Then a solution of the contact problem with such Coulomb friction solves also the problem with the original μ_k and any static friction greater than that limit.

Examples of kinetic friction:

Sliding friction is when two objects are rubbing against each other. Putting a book flat on a desk and moving it around is an example of sliding friction

Fluid friction is the friction between a solid object as it moves through a liquid or a gas. The drag of air on an airplane or of water on a swimmer are two examples of fluid friction.

Reducing friction

Devices

Devices, such as ball bearings can change sliding friction into much smaller rolling friction.

Techniques

One technique used by railroad engineers is to back up the train to create slack in the linkages between cars. This allows the train to pull forward and only take on the static friction of one car at a time, instead of all cars at once, thus spreading the static frictional force out over time.

Generally, when moving an object over a distance: To minimize work against static friction, the movement is performed in a single interval, if possible. To minimize work against kinetic friction, the movement is performed at the lowest velocity that's practical. This also minimizes frictional stress.

Lubricants

A common way to reduce friction is by using a lubricant, such as oil, that is placed between the two surfaces, often dramatically lessening the coefficient of friction. The science of friction and lubrication is called tribology. Lubricant technology is when lubricants are mixed with the application of science, especially to industrial or commercial objectives.

Superlubricity, a recently-discovered effect, has been observed in graphite: it is the substantial decrease of friction between two sliding objects, approaching zero levels (a very small amount of frictional energy would still be dissipated). Lubricants to overcome friction need not always be thin, turbulent fluids or powdery solids such as graphite and talc; acoustic lubrication actually uses sound as a lubricant.

Energy of friction

According to the law of conservation of energy, no energy is lost due to friction. Energy is transformed from other forms into heat. A sliding hockey puck comes to rest due to friction as its kinetic energy changes into heat. Since heat quickly dissipates many early philosophers, including Aristotle, wrongly concluded that moving objects lose energy without a driving force.

When an object is pushed along a surface, the energy converted to heat is given by:

E = N \mu_k d \,

where

N is the magnitude of the normal force,

μ_k is the coefficient of kinetic friction,

d is the distance travelled by the object while in contact with the surface.

Physical deformation is associated with friction. While this can be beneficial, as in polishing, it is often a problem, as the materials are worn away, and may no longer hold the specified tolerances. The work done by friction can translate into deformation and heat that in the long run may affect the surface's specification and the coefficient of friction itself. Friction can in some cases cause solid materials to melt.

References

Force | Introductory_physics

Gourt Home::Gourt :: Friction