Rotary engine

This article is about a piston engine. For internal combustion engines which do not use pistons, see pistonless rotary engine and Wankel engine. See also rotary engine (disambiguation).

The rotary engine was a common type of internal combustion aircraft engine in the early years of the 20th century. It was also used in a few motorcycles and cars.

In concept, a rotary engine is simple. It is a standard Otto cycle engine, but instead of having an orthodox fixed cylinder block with rotating crankshaft, the crankshaft remains stationary and the entire cylinder block rotates around it. In the most common form, the crankshaft was fixed solidly to an aircraft frame, and the propeller simply bolted onto the front of the cylinder block.

The effect of rotating such a large mass was an inherent large gyroscopic flywheel effect, smoothing out the power and reducing vibration. Vibration had been such a serious problem on other conventional piston engine designs that heavy flywheels had to be added. Because the cylinders themselves functioned as a flywheel, rotary piston engines typically had a power-to-weight ratio advantage over more conventional engines.

Most rotary engines were arranged with the cylinders pointed outwards from a single crankshaft, in the same general form as a radial, but there were also rotary boxer engines and even one cylinder rotaries.

History in aircraft

The first effective rotaries were built by Stephen Balzer, who was interested in the design for two main reasons:

In order to generate 100 hp (75 kW) at the low rpm at which the engines of the day ran, the pulsation resulting from each combustion stroke was quite large. In order to damp out these pulses, engines needed to mount a large flywheel, which added weight. In the rotary design the engine itself doubled as its flywheel, thus rotaries were lighter than similarly sized engines of regular design.
The cylinders had good airflow over them even when sitting still, which was an important concern given the alloys they had to work with at the time. Balzer's early engines did not even use cooling-fins, a feature of every other air-cooled design, and one that is complex and expensive to manufacture.

Another advantage, not realized at first, is that the pistons do not actually reciprocate; rather, they travel in a nearly-circular path around the common center of the connecting rods' "big ends", and only appear to reciprocate from the rotating frame of reference of the cylinders, which travel in a circle whose center is offset from that of the pistons (the centre of the crankshaft is offset from the engines centre of rotation). This lack of reciprocating mass leads to smoother running.

Cooling is another advantage of having rotating versus stationary engine block. Those early airplanes had relatively small cruising speed and the wind flow at 30 or 40 km/h was insufficient. Having a rotating engine at a few hundred rpm provided enough of cooling.

Balzer's first designs were ready for use in 1899, at which time they were the most advanced in the world. Other aircraft engines would not catch up in performance for a decade. He then became involved in Langley's Aerodrome attempts, which bankrupted him while he tried to make much larger versions.

The next major advance in the design was Louis and Laurent Seguin's Gnome series from 1908. Believed to have been inspired by the American Adams-Farwell automobile's rotary engine concept, they started their development with the seven cylinder Gnôme Omega No.1, which still exists and is in the collection of the Smithsonian's National Air and Space Museum. A production version of the Omega then soon reached the aviation market, still as a 7-cylinder 50 hp (37 kW), which soon reached 80 hp (60 kW), and then 110 hp (80 kW). The engine was at this later standard when WWI started, and the Gnome quickly found itself being used in a large number of aircraft designs. It was so good that it was licensed by a number of companies, including the German Oberursel firm, later purchased by Fokker. It was not at all uncommon for French Gnomes to meet German versions in combat.

The Gnome (and its copies) had a number of features that made it unique, even among the rotaries. Notably, the fuel was mixed and sprayed into the center of the engine through a hollow crankshaft, and then into the cylinders through the piston itself, a single valve on the top of the piston let the mixture in when opened. The valves were counter balanced so that only a small force was needed to open them, and releasing the force closed the valve without any springs. The center of the engine is normally where the oil would be, and the fuel would wash it away. To fix this, the oil was mixed in liberal quantities with the fuel, and the engine spewed smoke due to burning oil. Finally, the Gnome had no throttle or carburetor. Since the fuel was being sprayed into the spinning engine, the motion alone was enough to mix the fuel fairly well. Of course with no throttle, the engine was either on or off, so something as simple as reducing power for landing required the pilot to cut the ignition. "Blipping" the engine on and off gave the characteristic sputtering sound as though the engine was nearly stalling, though it did not stall as quickly as conventional engines due to its great rotational inertia.

Throughout the early period of the war, the power-to-weight ratio of the rotaries remained ahead of that of their competition. They were used almost universally in fighter aircraft, while traditional water cooled designs were used on larger aircraft. The engines had a number of disadvantages, notably very poor fuel consumption, partially because the engine was always "full throttle", and also because the valve timing was often less than ideal. The rotating mass of the engine made it, in effect, a large gyroscope. This could result in tricky handling. The Sopwith Camel, for example, was known to turn very nimbly to the right, but rather sluggishly to the left. Nevertheless, rotaries maintained their edge through a series of small upgrades, and many newer designs continued to use them.

As the war progressed, aircraft designers demanded ever-increasing amounts of power. Inline engines were able to meet this demand by improving their RPM, as more "bangs per minute" meant more power delivered. Improvements in valve timing, ignition systems and lighter materials made these higher RPM possible, and by the end of the war the average engine had increased from 1,200 RPM to 2,000. However the rotary was not able to use the same "trick," due to the drag of the cylinders through the air as they spun. For instance, if an early-war model of 1,200 RPM increased to only 1,400, the drag on the cylinders increased 36%, as air drag increases with the square of velocity. At lower speeds the drag could simply be ignored, but as speeds increased the rotary was putting more and more power into spinning the engine, and less into spinning the propeller.

One clever attempt to rescue the design was made by Siemens AG. The crankcase and cylinders spun counterclockwise at 900 RPM while the crankshaft spun clockwise at the same speed. This was achieved by the use of bevel gearing at the rear of the crankcase, resulting in the Siemens-Halske Sh.III, running at 1800 RPM with little net torque. It was also apparently the only rotary engine to use a regular style of throttleable carburetor, just as in an in-line engine. Used on the Siemens-Schuckert D.IV fighter, the new engine created what is considered by many to be the best aircraft of the war.

By the end of the war only a single new rotary powered aircraft was designed, Fokker's own D.VIII, designed solely to provide some use for their Oberursel factory's backlog of now-useless Ur.II 110 hp engines, themselves clones of the Le Rhône 9J rotary. When the war ended, the rotary disappeared almost instantly, with WWI engines being used for training for a short time until their poor fuel economy drove the users to newer engines.

Use in cars and motorcycles

Although the rotary engines were mostly used in aircraft, there were also a few cars and motorcycles with rotary engines. The most famous motorcycle (probably because of winning many races) is the Megola motorcycle with a radial rotary engine inside the front wheel. Another motorcycle with a radial rotary engine was the Redrup Radial, which had a rotating 3 cylinder engine in its frame.

In 1904, the Barry engine was built in Wales, a rotating 2 cylinder boxer engine inside a motorcycle frame, weighing 6.5 kg. In the 1940s Cyril Pullin developed the Powerwheel, a wheel with rotating one cylinder engine, clutch and drum brake inside the hub but it never went into serial production.

Cars with rotary engines were built (among others) by American companies Adams-Farwell, Bailey, Balzer and Intrepid.

Other Rotary Engines

Besides the configuration described in this article with cylinders moving around a fixed crankshaft, several other very different engine designs can also be described as rotary engines. The most notable of these, the Wankel rotary engine has also been used in cars (notably by Mazda), as well as in some experimental aviation applications.

External links

Aircraft piston engines | Engine technology | Piston engine configurations

Gourt Home::Gourt :: Rotary engine

History in aircraft

Use in cars and motorcycles

Other Rotary Engines

See also

External links