Gourt Home::Gourt :: Advanced Technology Attachment
Advanced Technology Attachment (ATA) is a standard interface for connecting storage devices such as hard disks and CD-ROM drives inside personal computers. Many terms and synonyms for ATA exist, including abbreviations such as IDE, ATAPI, and UDMA.
With the market introduction of Serial ATA in 2003, the original ATA was retroactively renamed Parallel ATA (PATA). In line with the original naming, this article only covers Parallel ATA.
Parallel ATA standards only allow cable lengths up to 46 centimetres (18 inches) although cables up to 91 cm (36 inches) can be readily purchased. Because of this length limit, the technology normally appears as an internal computer storage interface. It provides the most common and the least expensive interface for this application.
History
Although the standard has always had the official name "ATA", marketing dictates caused an early version to be dubbed Integrated Drive Electronics (IDE). This is due to the drive controller being contained on the drive itself as opposed to a separate controller connected to the motherboard. The standard following IDE, Enhanced IDE (EIDE) allowed the support of drives having a storage capacity larger than 528 megabytes (504 mebibytes), up to 8.4 gigabytes. Although these new names originated in branding convention and not as an official standard, the terms IDE and EIDE often appear as if interchangeable with ATA. This may be attributed to the two technologies being introduced with the same consumable devices, these "new" ATA hard drives. With the introduction of Serial ATA around 2003, conventional ATA was retroactively renamed to Parallel ATA (P-ATA), referring to the method in which data travels over wires in this interface.
The interface at first only worked with hard disks, but eventually an extended standard came to work with a variety of other devices—generally those using removable media. Principally, these devices include CD-ROM and DVD-ROM drives, tape drives, and large-capacity floppy drives such as the Zip drive and SuperDisk drive. The extension bears the name Advanced Technology Attachment Packet Interface (ATAPI), with the full standard now known as ATA/ATAPI.
The movement from programmed input/output (PIO) to direct memory access (DMA) provided another important transition in the history of ATA. As every computer word must be read by the CPU individually, PIO tends to be slow and use a lot of CPU. This is especially a problem on faster CPUs where accessing an address outside of the cacheable main memory (whether in the I/O map or the memory map) is a relatively expensive process. This meant that systems based around ATA devices generally performed disk-related activities much more slowly than computers using SCSI or other interfaces. However, DMA (and later Ultra DMA, or UDMA) greatly reduced the amount of processing time the CPU had to use in order to read and write the disks. This is possible because DMA and UDMA allow the disk controller to write data to memory directly, thus bypassing the CPU.
The original ATA specification used a 28-bit addressing mode. This allowed for the addressing of 228 (268,435,456) sectors of 512 bytes each, resulting in a maximum capacity of 137 gigabytes (128 GiB). The standard PC BIOS system supported up to 7.88 GiB (8.46 GB), with a maximum of 1024 cylinders, 256 heads and 63 sectors. Unfortunately, when the lowest common denominators of the CHS limitations in the standard PC BIOS system and the IDE standard were combined, the system as a whole was left limited to a mere 504 megabytes. BIOS translation and LBA were introduced, removing the need for the CHS structure on the drive itself to match that used by the BIOS and consequently allowing up to 7.88 GiB. With time, this limitation was itself lifted and first 32 GiB and then the full 128 GiB supported by ATA at that time became supported by PC BIOSes.
The newer specification allows 48-bit addressing, and this extends the limit to 128 PiB (or 144 petabytes).
These size limitations come about because some part of the system is unable to deal with block addresses above some limit. This problem may manifest itself by the system thinking the size of a drive is only the limit value, or by the system refusing to boot and hanging on the BIOS screen at the point when drives are initialized. In some cases, a BIOS upgrade for the motherboard will resolve the problem. This problem is also found in older external FireWire disk enclosures, which limit the usable size of a disk to 128 GB. By early 2005 most enclosures available have practically no limit. (Earlier versions of the popular Oxford 911 FireWire chipset had this problem. Later Oxford 911 versions and all Oxford 922 chips resolve the problem.)
Parallel ATA interface
Until the introduction of Serial ATA, 40-pin connectors generally attached drives to a ribbon cable. Each cable has two or three connectors, one of which plugs into a controller that interfaces with the rest of the computer system. The remaining one or two connectors plug into drives. Parallel ATA cables transfer data 16 bits at a time.
| Pin | Function | Pin | Function |
|---|---|---|---|
| 1 | Reset | 2 | Ground |
| 3 | Data 7 | 4 | Data 8 |
| 5 | Data 6 | 6 | Data 9 |
| 7 | Data 5 | 8 | Data 10 |
| 9 | Data 4 | 10 | Data 11 |
| 11 | Data 3 | 12 | Data 12 |
| 13 | Data 2 | 14 | Data 13 |
| 15 | Data 1 | 16 | Data 14 |
| 17 | Data 0 | 18 | Data 15 |
| 19 | Ground | 20 | Key |
| 21 | DDRQ | 22 | Ground |
| 23 | I/O Write | 24 | Ground |
| 25 | I/O Read | 26 | Ground |
| 27 | IOC HRDY | 28 | Cable Select |
| 29 | DDACK | 30 | Ground |
| 31 | IRQ | 32 | No Connect |
| 33 | Addr 1 | 34 | GPIO_DMA66_Detect |
| 35 | Addr 0 | 36 | Addr 2 |
| 37 | Chip Select 1P | 38 | Chip Select 3P |
| 39 | Activity | 40 | Ground |
Though the number of wires doubled, the number of connector pins and the pinout remain the same as on 40-conductor cables, and the external appearance of the connectors is identical. Internally, of course, the connectors are different: The connectors for the 80-wire cable connect a larger number of ground wires to a smaller number of ground pins, while the connectors for the 40-wire cable connect ground wires to ground pins one-for-one. 80-wire cables usually come with three differently colored connectors (blue, gray & black) as opposed to uniformly colored 40-wire cable's connectors (all black). The gray connector has pin 28 CSEL not connected ; this makes it the slave position for drives configured cable select.
The ATA standard has always specified a maximum cable length of just 46 cm (18 inches). This can cause difficulties in connecting drives within a large computer case, or when mounting several physical drives into one computer, and it all but completely eliminates the possibility of using parallel ATA for external devices. Although longer cables are widely available on the market, it must be understood that they are outside the parameters set by the specifications. The same is true of the "rounded" cables also commonly available: The ATA standard describes flat cables with particular impedance and capacitance characteristics. This is of course not a guarantee that other cables will not work, but an indication that nonstandard cables should be used, if at all, with caution.
If two devices attach to a single cable, one is commonly referred to as a master and the other as a slave. The master drive generally appears first when the computer's BIOS and/or operating system enumerates available drives. On old BIOSes (486 era and older) the drives are often misleadingly referred to by the bios as "C" for the master and "D" for the slave.
If there is a single device on a cable, in most cases it should be configured as master. However, some hard drives have a special setting called single for this configuration (Western Digital, in particular). Also, depending on the hardware and software available, a single drive on a cable can work reliably even though configured as the slave drive (this configuration is most often seen when a CDROM has a channel to itself).
A drive setting called cable select was described as optional in ATA-1 and has come into fairly widespread use with ATA-5 and later. A drive set to "cable select" automatically configures itself as master or slave, according to its position on the cable. Cable select is controlled by pin 28. The host controller grounds this pin; if a device sees that the pin is grounded, it becomes the master device; if it sees that pin 28 is open, the device becomes the slave device.
With the 40-wire cable it was very common to implement cable select by simply cutting this wire between the two device connectors. This puts the slave device at the end of the cable, and the master on the "middle" connector. This arrangement eventually was standardized in later versions of the specification. Unfortunately, if there is just one device on the cable, this results in an unused "stub" of cable. This is undesirable, both for physical convenience and electrical reasons: The stub causes signal reflections, particularly at higher transfer rates.
When the 80-wire cable was defined for use with UDMA4, these details were changed. The master device now goes at the end of the cable, so if there is only one device on the cable, there is no cable "stub" to cause reflections. Also, cable select is now implemented in the slave device connector, usually simply by omitting the contact from the connector body. Since 80-wire cables require special connectors anyway, this was a small additional effort. The standard also dictates color-coded connectors for easy identification by both installer and cable maker.
Although they are in extremely common use, the terms master and slave do not actually appear in current versions of the ATA specifications. The two devices are correctly referred to as device 0 (master) and device 1 (slave), respectively. It is a common myth that "the master drive arbitrates access to devices on the channel." In fact, the drivers in the host operating system perform the necessary arbitration and serialization. If device 1 is busy with a command then device 0 cannot start a command until device 1's command is complete, and vice versa. There is therefore no suggestion in the ATA protocols that one device has to ask the other if it can use the channel. Both are really "slaves" to the driver in the host OS.
ATA standards versions, transfer rates, and features
The following table shows the names of the versions of the ATA standards and the transfer modes and rates supported by each. Note that the transfer rate for each mode (for example, 66.7 MB/s for UDMA4, commonly called "Ultra-DMA 66") gives its maximum theoretical transfer rate on the cable. This is simply two bytes multiplied by the effective clock rate, and presumes that every clock cycle is used to transfer end-user data. In practice, of course, protocol overhead reduces this value.
Congestion on the host bus to which the ATA controller is attached may also limit the maximum burst transfer rate. For example, the maximum data transfer rate for conventional PCI bus is 133 MB/s, and this is shared among all active devices on the bus.
In addition, as of October 2005 no ATA hard drives exist capable of measured sustained transfer rates of above 80 MB/s. Furthermore, sustained transfer rate tests do not give realistic throughput expectations for most workloads: They use I/O loads specifically designed to encounter almost no delays from seek time or rotational latency. Hard drive performance under most workloads is limited first and second by those two factors; the transfer rate on the bus is a distant third in importance. Therefore, transfer speed limits above 66 MB/s only really affect performance when the hard drive can satisfy all I/O requests by reading from its internal cache — a very unusual situation, especially considering that such data is usually already buffered by the operating system.
| Standard | Other Names | Transfer Modes Added (MB/s) | Maximum disk size | Other New Features | ANSI Reference |
|---|---|---|---|---|---|
| ATA-1 | ATA, IDE | PIO 0,1,2 (3.3, 5.2, 8.3) Single-word DMA 0,1,2 (2.1, 4.2, 8.3) Multi-word DMA 0 (4.2) | up to 137 GB | X3.221-1994 (obsolete since 1999) | |
| ATA-2 | EIDE, Fast ATA, Fast IDE, Ultra ATA | PIO 3,4: (11.1, 16.6) Multi-word DMA 1,2 (13.3, 16,6) | 28-bit logical block addressing (LBA) | X3.279-1996 (obsolete since 2001) | |
| ATA-3 | EIDE | S.M.A.R.T., Security | X3.298-1997 (obsolete since 2002) | ||
| ATA/ATAPI-4 | ATA-4, Ultra ATA/33 | Ultra DMA 0,1,2 (16.7, 25.0, 33.3) aka Ultra-DMA/33 | Support for CD-ROM, etc., via ATAPI packet commands | NCITS 317-1998 | |
| ATA/ATAPI-5 | ATA-5, Ultra ATA/66 | Ultra DMA 3,4 (44.4, 66.7) aka Ultra DMA 66 | 80-wire cables | NCITS 340-2000 | |
| ATA/ATAPI-6 | ATA-6, Ultra ATA/100 | UDMA 5 (100) aka Ultra DMA 100 | up to 144 PB | 48-bit LBA Automatic Acoustic Management | NCITS 347-2001 |
| ATA/ATAPI-7 | ATA-7, Ultra ATA/133 | UDMA 6 (133) aka Ultra DMA 133 SATA/150 | SATA 1.0, Streaming feature set, long logical/physical sector feature set for non-packet devices | NCITS 361-2002 | |
| ATA/ATAPI-8 | ATA-8 | -- | -- | in progress |
In August 2004, Sam Hopkins and Brantley Coile of Coraid specified a lightweight protocol to carry ATA commands over Ethernet instead of directly connecting them to a PATA host controller. This permitted the established block protocol to be reused in Network-attached storage applications.
See also
- Serial ATA (SATA)
External links
- Overview and History of the IDE/ATA Interface
- ATA/ATAPI history
- Enhanced IDE/Fast-ATA/ATA-2 FAQ
- Hard Drive Size Barriers
- T13 Technical Standards Group
- Computer Interface Help and Information
- How to solve one well known dma-mode problem in WinXP
Advanced Technology Attachment
IDE | ATA/ATAPI | Integrated Drive Electronics | Integrated drive electronics | Advanced Technology Attachment | Advanced Technology Attachment | ATA | ATA | Ata | Integrated Drive Electronics | Advanced Technology Attachment | ATA | ATA | ATA | ATA | IDE | IDE | Ata | پیشرفتہ طرزی وابستگی | 集成设备电路
"Advanced Technology Attachment"